Shulou(Shulou.com)06/01 Report--

This article mainly shows you "how to install Windows 7 will not fail", the content is easy to understand, clear, hope to help you solve your doubts, the following let the editor lead you to study and learn "how to install Windows 7 will not fail" this article.

Since Microsoft released Windows 7, many people have become users of Windows 7. However, some users' installation is bound to fail, and there are many reasons why the installation of Windows 7 cannot continue. According to the author's experience, the main reason is that the hardware components are not compatible or the hardware configuration of the system can not meet the requirements of installing Windows 7, so when troubleshooting, we should focus on this aspect and avoid detours. Below, the author enumerates several most typical situations for analysis.

(1)。 Setup refuses to install or start

If the hardware components are not compatible with Windows 7, the installation may fail or the installer cannot be started. So make sure that all the system hardware is detected by Windows 7 before installation, and that it is included in the hardware compatibility list (HCL) of Windows 7. It is recommended that you do the necessary compatibility check before installing Windows 7. If you have already started the installation, it will be too late to check the compatibility.

If it is an upgrade installation or dual-system installation, I think we can restart to the original system, and then start the installer with the following parameters to test. "/ 1394debug:", enable kernel debugging on a specific channel of the IEEE1394 port. "/ debug", enable kernel debugging through the COM1 or COM2 port. "/ usbdebug:" enable kernel debugging through the USB port of a specific target device. These options put the installer in debug mode and help determine the cause of the failure. If the installer detects a hardware conflict, you can configure the hardware to eliminate the conflict.

(2)。 Setup reports media or DVD errors

If you install directly from the installation CD of Windows 7, or if you install from the network by publishing shares, you may also encounter media errors that cause the installation to fail. For installation from DVD, we can try to clean the DVD optical drive so that it can read the disk better, or replace the optical drive or CD. For enterprise users, the client generally carries on the shared installation from the shared release, generally, the sharing does not contain all the installation files, or there is a problem with the network connection to the shared, we can troubleshoot from these two aspects.

(3)。 The installer reports insufficient system resources

Microsoft recently announced the hardware resource requirements for the Windows 7 installation, at least 512MB memory and approximately 25GB hard disk space. For some older sub-users, the installer cannot start if the memory requirements of the Windows 7 installation are not met. If the installer can start but detects that there is insufficient hard disk space, it will not be able to install unless we rebuild the partition, or delete the original partition, and have enough space to install the operating system. For this type of installation failure, Windows 7 will have a clear error prompt, and of course it is very easy to troubleshoot.

(4)。 The installer suddenly stopped responding.

Excluding all the above factors, sometimes we are lucky to encounter the corresponding situation where the installer suddenly stops. Usually, the installation of Windows 7 was going well, but suddenly we found that the installation stopped responding and stopped the installation without any progress in the current interface. In this case, sometimes we will see an error message from stop, sometimes there is nothing, and the system seems to have crashed.

If there is an error prompt to install stop, but most stop errors are obscure error codes that don't tell us exactly what went wrong. At this point, we can write down these error numbers or codes with a pen, then go to the Microsoft knowledge Base (click to enter) for detailed information, and then troubleshoot. Installation can not proceed at this time, we usually need to press the Ctrl+Alt+Del key to restart the computer to interrupt the error, sometimes press the key combination is not effective, we need to press the power button on the computer to force the system to restart.

Normally, after we restart the computer, we will go directly to the installation program, and the installation will continue. In some cases, you may also see the startup menu, and if this is the case, we can select the Windows installer option to allow setup to continue. If the installer stops responding again, you need to restart your computer, and sometimes you may need to try multiple times to complete the installation. Such failures are usually caused by sudden factors, and rebooting can solve the problem. However, memory and CPU can also be the root cause of the problem, which requires us to do more complex troubleshooting, and replacing hardware will usually solve the problem.

The above is all the contents of the article "how to install Windows 7 will not fail". Thank you for reading! I believe we all have a certain understanding, hope to share the content to help you, if you want to learn more knowledge, welcome to follow the industry information channel!

Welcome to subscribe "Shulou Technology Information " to get latest news, interesting things and hot topics in the IT industry, and controls the hottest and latest Internet news, technology news and IT industry trends.