Shulou(Shulou.com)06/03 Report--

Time/System Time time / system time

Date/System Date date / system date

Level 2 Cache secondary cache

System Memory system memory

Video Controller video controller

Panel Type LCD model

Audio Controller Audio Controller

Modem Controller Modem (Modem)

Primary Hard Drive main hard disk

Modular Bay module carrier

Service Tag Service tag

Asset Tag Asset label

BIOS Version BIOS version

Boot Order/Boot Sequence boot sequence (the order in which the system searches for * * as system files)

Diskette Drive floppy disk drive

Internal HDD internal hard drive

Floppy device floppy drive device

Hard-Disk Drive hard disk drive

USB Storage Device USB storage device

CD/DVD/CD-RW Drive optical drive

CD-ROM device optical drive

Modular Bay HDD modular hard disk drive

Cardbus NIC Cardbus bus network card

Onboard NIC onboard network card

Boot POST level of hardware check at post (POST): if set to "MINIMAL" (the default), post is checked only if the BIOS upgrade, memory module changes, or previous post did not complete. Set to "THOROUGH" to perform a full set of hardware checks at post.

Config Warnings warning setting: this option is used to set whether to alarm when the system uses a low-voltage power adapter or other unsupported configuration, set to "DISABLED" to disable alarm, set to "ENABLED" to enable alarm

Internal Modem built-in modem: use this option to enable or disable built-in Modem. Modem is not visible in the * * operating system when disabled is disabled.

LAN Controller Network Controller: use this option to enable or disable the PCI Ethernet controller. After disabling, the device is not visible in the system.

PXE BIS Policy/PXE BIS Default Policy PXE BIS policy: this option controls how the system handles authorization requests (starting the overall service Boot Integrity Services (BIS)) without authentication. The system can accept or reject BIS requests. When set to Reset, BIS will be reinitialized and set to Deny the next time the computer is started.

Onboard Bluetooth on-board Bluetooth device

MiniPCI Device MiniPCI equipment

MiniPCI Status MiniPCI device status: you can use this option to enable or disable onboard PCI devices when installing MiniPCI devices

Wireless Control wireless control: use this option to set the control mode of MiniPCI and Bluetooth wireless devices. When set to "Application", wireless devices can be enabled or disabled through applications such as "Quickset", and hotkeys are not available. When set to "/ Application", wireless devices can be enabled or disabled through applications such as "Quickset" or hotkeys. The wireless device is disabled when set to "Always Off" and cannot be enabled in the * * system.

Wireless wireless devices: use this option to enable or disable wireless devices. This setting can be changed through the "Quickset" or "" hotkeys in the system. Whether this setting is available depends on the setting of "Wireless Control".

Serial Port serial port: this option avoids device resource conflicts by reassigning port addresses or disabling ports.

Infrared Data Port infrared data port. Use this setting to avoid device resource conflicts by reassigning port addresses or disabling ports.

Parallel Mode parallel port mode. Controls whether the parallel port of the computer works as "NORMAL" (AT compatible) (common standard parallel port), "BI-DIRECTIONAL" (PS/2 compatible) (bi-directional mode, which allows two-way communication between host and peripherals) or "ECP" (Extended Capabilities Ports, extended function port) (default).

Num Lock digital lock. Sets whether the digital light (NumLock LED) is lit when the system starts. Set to "DISABLE" to keep the digital light off, and set to "ENABLE" to turn on the digital light when the system starts.

Keyboard NumLock keyboard digital lock: this option is used to set whether keyboard-related error messages are prompted when the system starts.

Enable Keypad enable keypad: set to "BY NUMLOCK" to enable the numeric keypad when the NumLock light is on and there is no external keyboard. Set to "Only By Key" to keep the embedded keypad disabled when the NumLock light is on.

External Hot Key external hotkeys: this setting allows keys to be used on an external PS/2 keyboard in the same way as keys on a laptop. If you use ACPI** as a system, such as Win2000 or WinXP, the USB keyboard cannot use keys. Keys are only available on the USB keyboard in pure DOS mode. Set to "SCROLL LOCK" (the default option) to enable this feature, and set to "NOT INSTALLED" to disable it.

USB EmulationUSB emulation: use this option to use USB keyboard, USB mouse and USB floppy drive in operating systems that do not directly support USB. This setting is automatically enabled during BIOS startup. When this feature is enabled, the simulation continues to be valid when control is transferred to the system. After disabling this feature, the simulation is turned off when the control is transferred to the system.

Pointing Device pointer device: the external serial mouse is enabled and the integrated touchpad is disabled when set to "SERIAL MOUSE". When set to "PS/2 MOUSE", if an external PS/2 mouse is attached, the integrated touchpad is disabled. When set to "TOUCH PAD-PS/2 MOUSE" (the default), you can switch between the mouse and the touchpad if you have an external PS/2 mouse. The changes take effect after the computer restarts.

Video Expansion video extension: use this option to enable or disable video extension to adjust the lower resolution to a higher, normal LCD resolution.

Battery battery

Battery Status battery statu

Power Management Power Management

Suspend Mode** start mode

AC Power Recovery AC power recovery: this option reflects the response of the computer when the AC power adapter is plugged back into the system.

Welcome to subscribe "Shulou Technology Information " to get latest news, interesting things and hot topics in the IT industry, and controls the hottest and latest Internet news, technology news and IT industry trends.