Shulou(Shulou.com)06/03 Report--

This article mainly introduces "BIOS Chinese and English comparison Table Summary". In daily operation, I believe many people have doubts about the summary of BIOS Chinese and English comparison tables. The editor consulted all kinds of data and sorted out simple and easy-to-use operation methods. I hope it will be helpful to answer the doubts of "BIOS Chinese and English comparison Table Summary"! Next, please follow the editor to study!

Time/System Time time / system time

Date/System Date date / system date

Level 2 Cache secondary cache

System Memory system memory

Video Controller video controller

Panel Type LCD model

Audio Controller Audio Controller

Modem Controller Modem (Modem)

Primary Hard Drive main hard disk

Modular Bay module carrier

Service Tag Service tag

Asset Tag Asset label

BIOS Version BIOS version

Boot Order/Boot Sequence boot sequence (the order in which the system searches for operating system files)

Diskette Drive floppy disk drive

Internal HDD internal hard drive

Floppy device floppy drive device

Hard-Disk Drive hard disk drive

USB Storage Device USB storage device

CD/DVD/CD-RW Drive optical drive

CD-ROM device optical drive

Modular Bay HDD modular hard disk drive

Cardbus NIC Cardbus bus network card

Onboard NIC onboard network card

Boot POST

Level of hardware check at post (POST): if set to "MINIMAL" (the default), post is checked only if the BIOS is upgraded, the memory module is changed, or the previous post did not complete. Set to "THOROUGH" to perform a full set of hardware checks at post.

Config Warnings

Warning setting: this option is used to set whether to alarm when the system uses a low-voltage power adapter or other unsupported configuration, set to "DISABLED" to disable alarm, set to "ENABLED" to enable alarm

Internal Modem

Built-in modem: use this option to enable or disable the built-in Modem. When disabled (disabled), Modem is not visible in the operating system.

LAN Controller

Network Controller: use this option to enable or disable the PCI Ethernet controller. When disabled, the device is not visible in the operating system.

PXE BIS Policy/PXE BIS Default Policy

PXE BIS policy: this option controls how the system handles authorization requests (starting the overall service Boot Integrity Services (BIS)) without authentication. The system can accept or reject BIS requests. When set to Reset, BIS will be reinitialized and set to Deny the next time the computer is started.

Onboard Bluetooth on-board Bluetooth device

MiniPCI Device MiniPCI equipment

MiniPCI Status MiniPCI device status: you can use this option to enable or disable onboard PCI devices when installing MiniPCI devices

Wireless Control

Wireless control: use this option to set the control mode of MiniPCI and Bluetooth wireless devices. When set to "Application", wireless devices can be enabled or disabled through applications such as "Quickset", and hotkeys are not available. When set to "/ Application", wireless devices can be enabled or disabled through applications such as "Quickset" or hotkeys. The wireless device is disabled when set to "Always Off" and cannot be enabled in the operating system.

Wireless

Wireless devices: use this option to enable or disable wireless devices. This setting can be changed in the operating system through the "Quickset" or "" hotkeys. Whether this setting is available depends on the setting of "Wireless Control".

Serial Port serial port: this option avoids device resource conflicts by reassigning port addresses or disabling ports.

Infrared Data Port infrared data port. Use this setting to avoid device resource conflicts by reassigning port addresses or disabling ports.

Parallel Mode

Parallel port mode. Controls whether the parallel port of the computer works as "NORMAL" (AT compatible) (common standard parallel port), "BI-DIRECTIONAL" (PS/2 compatible) (bi-directional mode, which allows two-way communication between host and peripherals) or "ECP" (Extended Capabilities Ports, extended function port) (default).

Num Lock

Digital lock. Sets whether the digital light (NumLock LED) is lit when the system starts. Set to "DISABLE" to keep the digital light off, and set to "ENABLE" to turn on the digital light when the system starts.

Keyboard NumLock keyboard digital lock: this option is used to set whether keyboard-related error messages are prompted when the system starts.

Enable Keypad

Enable keypad: set to "BY NUMLOCK" to enable the numeric keypad when the NumLock light is on and there is no external keyboard. Set to "Only By Key" to keep the embedded keypad disabled when the NumLock light is on.

External Hot Key

External hotkeys: this setting allows keys to be used on an external PS/2 keyboard in the same way as keys on a laptop. If you are using an ACPI operating system, such as Win2000 or WinXP, the USB keyboard cannot use keys. Keys are only available on the USB keyboard in pure DOS mode. Set to "SCROLL LOCK" (the default option) to enable this feature, and set to "NOT INSTALLED" to disable it.

USB Emulation

USB emulation: use this option to use the USB keyboard, USB mouse, and USB floppy drive in operating systems that do not directly support USB. This setting is automatically enabled during BIOS startup. When enabled, the simulation continues to be valid when control is transferred to the operating system. After disabling this feature, the simulation is turned off when control is transferred to the operating system.

Pointing Device

Pointer device: the external serial mouse is enabled and the integrated touchpad is disabled when set to "SERIAL MOUSE". When set to "PS/2 MOUSE", if an external PS/2 mouse is attached, the integrated touchpad is disabled. When set to "TOUCH PAD-PS/2 MOUSE" (the default), you can switch between the mouse and the touchpad if you have an external PS/2 mouse. The changes take effect after the computer restarts.

Video Expansion

Video extension: use this option to enable or disable video extension to adjust the lower resolution to a higher, normal LCD resolution.

Battery battery

Battery Status battery statu

Power Management Power Management

Suspend Mode pending mode

AC Power Recovery AC power recovery: this option reflects the response of the computer when the AC power adapter is plugged back into the system.

Low Power Mode low Power Mode: this option is used to set the amount of power used when the system hibernates or shuts down.

Brightness

Brightness: this option sets the brightness of the monitor when the computer starts up. The default setting is half when the computer is working in the power supply state. The default setting is maximum when the computer is working with the AC power adapter.

Wakeup On LAN

Network Wake up: this setting allows the computer to wake up from hibernation when the network signal is connected. This setting is not valid for standby state (Standby state). You can only wake up standby in the operating system. This setting is valid only when an AC power adapter is connected.

Auto On Mod auto-boot mode: note that this setting will not take effect if the AC power adapter is not connected. This option sets the automatic boot time of the computer, and you can set the computer to power on automatically every day or only on weekdays. The settings take effect after the computer restarts.

Auto On Time automatic boot time: this option sets the automatic boot time of the system, the time format is 24-hour system. Type a numeric value or use the left and right arrow keys to set the numeric value. The settings take effect after the computer restarts.

Dock Configuration docking station configuration

Docking Status docking station statu

Universal Connect Universal Interface: this setting is invalid if the operating system you are using is WinNT4.0 or earlier. If you frequently use more than one Dell docking device and want to minimize the initial time when docked, set it to "ENABLED" (the default setting). If you want the operating system to generate a new system settings file for each new docking device connected to the computer, set it to DISABLED.

System Security system security

Primary Password master password

Admin Password administrative password

Hard-disk drive password (s) hard disk drive password

Password Status

Password status: this option is used to lock the system password when the Setup password is enabled. Set this option to "Locked" and enable the Setup password to place the system password changed. This option can also be used to place passwords that are disabled by the user when the system starts.

System Password system password

Setup Password Setup password

Post Hotkeys self-test hotkey: this option is used to specify the hotkey (F2 or F12) that appears on the screen during power on self-test (POST).

Chassis Intrusion

Chassis anti-theft: this option is used to enable or disable chassis anti-theft detection features. When set to "Enable-Silent", if chassis intrusion is detected at startup, no warning message will be sent. When this option is enabled and the chassis cover is open, the domain will display "DETECTED".

Drive Configuration Drive Settings

Diskette Drive A: disk drive A: if a floppy drive is installed in the system, use this option to enable or disable the floppy drive

Primary Master Drive first master drive

Primary Slave Drive first slave drive

Secondary Master Drive second primary drive

Secondary Slave Drive second slave drive

IDE Drive UDMA supports IDE drives for UDMA: use this option to enable or disable DMA transfer through the internal IDE hard disk interface.

Hard-Disk drive Sequence hard disk drive order

System BIOS boot devices system BIOS boot sequence

USB device USB equipment

Memory Information memory information

Installed System Memory system memory: this option displays the size and type of memory installed in the system

System Memory Speed memory rate: this option displays the rate of installed memory

System Memory Channel Mode memory channel mode: this option displays memory slot settings.

AGP Aperture AGP area memory capacity: this option specifies the memory value allocated to the video adapter. Some video adapters may require more than the default amount of memory.

CPU information CPU information

CPU Speed CPU rate: this option displays the running rate of the CPU after startup

Bus Speed bus rate: display processor bus rate

Processor 0 ID processor ID: displays the type and model number of the processor

Clock Speed clock frequency

Cache Size cache value: displays the secondary cache value of the processor

Integrated Devices (LegacySelect Options) integrated device

Sound sound settings: use this option to enable or disable the audio controller

Network Interface Controller network interface controller: enable or disable integrated network card

Mouse Port mouse port: use this option to enable or disable the built-in PS/2 compatible mouse controller

USB Controller USB controller: use this option to enable or disable the onboard USB controller.

PCI Slots PCI slot: use this option to enable or disable onboard PCI card slots. When disabled, all PCI cards are not available and cannot be detected by the operating system.

Serial Port 1

Serial port 1: use this option to control the operation of the built-in serial port. When set to "AUTO", if two devices are used on the same port address through the serial port expansion card, the built-in serial port automatically reassigns the available port address. Serial ports use COM1 first, then COM2, and if both addresses are assigned to a port, the port will be disabled. .

Parallel Port parallel port: the built-in parallel port can be configured in this domain

Mode

Mode: when set to "AT", the built-in parallel port can only output data to connected devices. The parallel port can input and output data when it is set to PS/2, EPP or ECP mode. The protocols used in these three modes are different from the most big data transmission rate. Maximum transmission rate PS/2

At this point, the study on the "BIOS Chinese and English comparison Table Summary" is over. I hope to be able to solve your doubts. The collocation of theory and practice can better help you learn, go and try it! If you want to continue to learn more related knowledge, please continue to follow the website, the editor will continue to work hard to bring you more practical articles!

Welcome to subscribe "Shulou Technology Information " to get latest news, interesting things and hot topics in the IT industry, and controls the hottest and latest Internet news, technology news and IT industry trends.