In addition to Weibo, there is also WeChat
Please pay attention
WeChat public account
Shulou
2025-03-29 Update From: SLTechnology News&Howtos shulou NAV: SLTechnology News&Howtos > Internet Technology >
Share
Shulou(Shulou.com)06/02 Report--
This article will explain in detail how to use the pads modeless command, the content of the article is of high quality, so the editor will share it for you as a reference. I hope you will have a certain understanding of the relevant knowledge after reading this article.
Global Settings (Global Settings)
C. . Turns on or off the supplementary format display mode of the design screen.
D. . Turns the current layer on or off with the highest priority.
DO... . Turn on to turn off the current through hole display mode.
ET... . When setting the suspension line, the test point is used as the end mode.
I. . Conduct a complete database test.
L. . Change the current layer, for example, the current layer is the second layer
N. . Highlight a certain network
O. . Display the pads and wiring as their outer frames.
PO... . Only the outer frame of the copper will be displayed.
Q. . Open the Quick Meter and start the measurement at the current position.
QL... . The total length of the lighted network, pin alignment and a certain range of selection are measured quickly.
R. . Set the minimum display lineweight, and if it is less than this value, only its midline is displayed, for example.
RV... . Maintain the establishment of repetitive use of circuit patterns.
SPD... . Displays the data that generates the hybrid split layer.
SPI... . Displays the hot pad marking symbol "" on its hot pad.
SPO... . Only the bounding box of the mixed split layer is displayed.
T. . Set the design screen to transparent display mode.
X. . Turns text bounding box display on or off.
W. Change the linewidth, such as 30.
Grid (Grids)
G. Through holes and design grid settings.
GD... Displays grid settings.
GP... Turns the polar grid on or off.
GP r a... Moves to a specified polar coordinate point.
GPR r. Moves a point with a specified radial radius under the condition of a certain angle.
GPA a moves at a specified angle under the condition of a certain radial radius.
GPRA da... Under the condition of a certain radial radius, move according to the current angle.
GPRR dr... Under the condition of a certain angle, it moves according to the current radial radius.
GR... Set up the design grid.
GV... Set the through-hole grid.
Search (Search)
S. Search for component pins or components.
S. Search for an absolute coordinate point, such as 15001200.
SR... Search for a relative coordinate point.
SRX... Keep the current coordinates unchanged and search for a relative coordinate point.
SRY... Keep the current coordinates unchanged and search for a relative coordinate point.
SS... Search for or select one or a class of non-artifacts because this command supports wildcard symbols.
SX... Leave the current coordinates unchanged and move to a specified absolute coordinate point.
SY... Leave the current coordinates unchanged and move to a specified absolute coordinate point.
SP... Search for or select segments that use pixel faces that are not lineweights.
Angle (Angles)
AA... Switch to any angle mode.
AD... Switch to bevel mode.
AO... Switch to right-angle mode.
Cancel (Undo)
UN []. The operation can be canceled multiple times because it is variable.
RE []. Repeat the operation multiple times.
Design rules check DRC (Design Rules Checking)
DRP... It is forbidden to violate the design rules.
DRW... Violation of warning mode.
DRI... Ignore design rules.
DRO... Completely close the design rules.
On-line (Routing)
E. End with no through hole to suspend the wiring.
LD... Use the front layer alignment for straight or horizontal aspects.
PL... Lock the current operation layer pair.
SH... Turns push mode on or off.
V. Select the type of via that is currently used.
VA... Automatic through hole selection.
VP... Use buried hole or blind hole through hole.
VT... Use through hole type through hole.
T. Use transparent mode.
Draw objects (Drafting Objects)
HC... Switch to drawing circle graphics mode.
HH... Switch to drawing non-closed graphics mode.
HP... Switch to draw polygon graphics mode.
HR... Switch to drawing rectangle graphics mode.
Alternate mouse click (Mouse Click Substitutes)
M. Activating the pop-up menu in the current functional mode is equivalent to right-clicking.
Spacebar... It is equivalent to clicking the left mouse button at the current crosshairs, such as increasing the corner of the alignment.
Other aspects (Various)
?. Displays the current help topic.
BMW... Open the conversation window.
BLT... Open the conversation window.
F. Open the file, for the path and name of the open file.
On how to use the pads modeless command to share here, I hope the above content can be of some help to you, can learn more knowledge. If you think the article is good, you can share it for more people to see.
Welcome to subscribe "Shulou Technology Information " to get latest news, interesting things and hot topics in the IT industry, and controls the hottest and latest Internet news, technology news and IT industry trends.
Views: 0
*The comments in the above article only represent the author's personal views and do not represent the views and positions of this website. If you have more insights, please feel free to contribute and share.
Continue with the installation of the previous hadoop.First, install zookooper1. Decompress zookoope
"Every 5-10 years, there's a rare product, a really special, very unusual product that's the most un
© 2024 shulou.com SLNews company. All rights reserved.