Shulou(Shulou.com)05/31 Report--

Hello everyone, Lin Fei to answer the above questions, professional cleaning range hood process, professional cleaning range hood many people do not know, now let's take a look!

Do you know how to clean the range hood? After each cooking, let the range hood run continuously for 30 seconds to 1 minute, and extract the oil fume and water vapor left in the air as well as unburned carbon monoxide. Take advantage of the residual heat on the range hood, wipe the surface with a dishcloth, you can easily wipe off the oil stains on the range hood, and often keep it clean and non-greasy. Learn the following techniques for cleaning range hood with Bian Shaw? Yes.

[cleaning method of range hood] Tips on how to clean the range hood

Due to the accumulation of lampblack for a long time, a large number of stubborn oil stains have been accumulated inside the lampblack machine, which is more troublesome to clean up. If we want to clean up the stubborn oil stains thoroughly, we can directly buy the professional range hood cleaning service provided by SUNING's gang.

SUNING customers use high-temperature steam cleaning, which can effectively protect the health of their families. SUNING gang uses professional tools, the implementation of standardized services, internal and external deep cleaning, take on a new look. Customized full-function professional cleaning equipment to achieve 360-degree steam disinfection without dead corner. The key point is clean and waterproof, professional household appliance protective cover is dustproof and waterproof. There is no extra charge for cleaning services, and there are often preferential activities. Cleaning multiple range hood or any combination of electrical appliances has other benefits. Please click on the picture below for more details.

In general, the installation height of the range hood is on the same axis as the range hood, and the left, front and rear positions should be kept horizontal. The distance from the bottom of the range hood to the kitchen surface should be 650~750mm (side suction machine can be appropriately reduced (200~400mm), depending on the specific use). The range hood should not be installed in places where the air convection is strong. When installing, you can draw the approximate position on the wall with a pencil.

1. In general, the outer edge of the range hood is 650700 mm away from the gas stove. It can also be determined according to the overall situation. It should be lower than higher. The range hood should be installed directly above the center of the gas stove, and the distance between its bottom and the gas stove should be in the range of 650 ~ 750mm.

two。 The Chinese deep machine with smoke cover can be installed higher, those without smoke cover can be installed lower, those with high power can be installed higher, and those with low power can be installed lower.

3. The installation of the application common flue is lower, and the installation of the application common flue is higher. Try not to install the range hood near doors and windows and other places with strong air convection, so as not to affect the effect of lampblack suction.

4. The outlet pipe should not be too long, it is best not to exceed 2m, reduce bending as far as possible, avoid 90-degree bending many times, otherwise it will affect the effect of lampblack.

In order to make things simple and convenient, some families usually hire professionals to clean the range hood, but it costs 100 yuan for professionals to clean the range hood, which actually brings hidden dangers to the use of the machine. Therefore, do it yourself, have plenty of food and clothing, and keep the range hood clean every day.

How to clean the range hood? Next, let's learn some tips for cleaning range hood with Bian Shaw.

The professional cleaning method of the range hood is to take the range hood apart and then soak all the spare parts in a container full of soda water. Where the oil is particularly thick, it needs to be scraped off with a sharp blade, then cleaned, finally dried, installed and used. In this process, it is easy to find the following problems: first, it damages the life of the machine. The range hood has high requirements for dynamic balance because of its high-speed rotation. Cleaners who do not have much mechanical knowledge are likely to destroy the dynamic balance during disassembly and cleaning, thus increasing the resistance and noise of fan bearings, resulting in serious consequences such as increased noise, poor stability, jitter during machine operation, reduction of exhaust air volume and so on. Secondly, due to the soaking of high-strength soda water and the scratching of sharp tools, it is easy to seriously damage the protective film on the surface of the range hood, making it easier for the range hood to stick to oil.

In fact, it is very simple to solve the cleaning problem of the range hood. First of all, to avoid disassembly and cleaning, to ensure that the range hood will not be damaged. Secondly, it is

1. Clean the cigarette machine while it is hot after each use.

Adhere to the daily cleaning of the cigarette machine, can save the big trouble of cleaning up at the end of last year. After each cooking, let the range hood run continuously for 30 seconds to 1 minute, and draw the residual lampblack and water vapor as well as unburned carbon monoxide out of the house. Take advantage of the residual heat on the range hood, wipe the surface with a dishcloth, you can easily wipe off the oil stains on the range hood, and often keep it clean and non-greasy.

two。 Do oil-proof treatment before using the new range hood.

Before using the new range hood, sprinkle a thin layer of soap powder on the two oil storage boxes, and then inject about 1/3 of the water. In this way, the recovered oil floats on the surface of the water instead of freezing and condensing on the wall of the box. When the waste oil is full, pour it and then do the same thing. How to prevent the fuselage of range hood from coming out of oil? Before using it, we can dip a little wet dishcloth with dishwashing essence. No water, wipe the car body, wipe the fan leaves as much as possible. After natural drying, the detergent coating to prevent lampblack adhesion is completed. After a while, if the fuselage feels sticky, it should be cleaned. Because there is a "protective coating" between the oil and the fuselage. So if you directly clean the fuselage with 80% hot water, the oil will be washed down first. After cleaning, don't forget to apply the detergent on the fuselage again. It should be a little thicker, the humidity should be controlled at a non-dripping level, and then cover the key with plastic wrap.

3. Cleaning of oil net and oil storage box

You can slowly remove the net with a screwdriver, spray lampblack, put it in a plastic bag, let it sit for 15 minutes, and then take it out. After injecting 80% hot water into the basin, wash it carefully with a dishcloth. If the grease on the oil net is very thick, you can also gently scrape off some of the grease with a thin piece of bamboo before cleaning. Stick a layer of cling film in the oil storage box, and part of the cling film should stick out of the oil storage box and completely cover the original table in the box.

4. Four wonderful ways to clean the fan blade

Must "lampblack net" be used in the cleaning of range hood blades? Not necessarily. Although, the oil fume net has a strong saponification and emulsifying ability to the oil stain on the fuselage and fan leaves, after covering the table under the lampblack machine with a newspaper, spray the lampblack net on the fuselage and fan blades, turn on the lampblack machine a few minutes later, and use the centrifugal force of the fan to remove the oil fume and the dissolved dirty oil; wipe it again with wet paper towels, and the cleaning of the fuselage and fan blades will be done at home. However, lampblack net is, after all, a chemical product, which has a certain stimulating effect on the skin and respiratory mucosa, so we'd better use less. Here are four kinds of fan deoiling methods of "no use of lampblack". You can try it.

Step 1

Soak in detergent and vinegar. Remove the leaves carefully and soak them in a pot of hot water mixed with 2ml detergent and 50ml vinegar. Soak for about 15 minutes, then scrub with a clean rag. The fuselage of the range hood is also cleaned with this solution. Attention should be paid to keeping the humidity of the solution at about 60 ℃ for decontamination. This self-prepared cleaning solution has been proved to be non-irritating to the skin and intraocular mucosa of the hand, no corrosion to the range hood, and the surface still maintains the original luster after cleaning.

Step 2

Pressure cooker steam washing method. Put half a pot of cold water in the pressure cooker and bring it to a boil. When the steam is continuously discharged, take the lower pressure limit valve, open the range hood and aim the steam water column at the rotating blade. As the high hot water steam constantly rushes down the fan leaves, the oil will flow into the waste oil tank along the oil drain.

Step 3

After drying the washed fan leaves, apply a layer of office glue. After a few months of use, tear off the oil stains on the fan leaves, and all the oil stains are stained on the glue layer, so that the cleaning is convenient and clean.

Step 4

First spread the newspaper on the stove, turn on the switch of the range hood to "preheat" the fan for two minutes, spray detergent to the fan of the range hood, turn off the range hood, rest for three minutes, then spray 60 ℃ of hot water into the fan of the range hood, and then turn on the switch to let the dissolved oil drop into the oil storage box to complete the cleaning.

At the end of this article, I hope it will be helpful to you.

Welcome to subscribe "Shulou Technology Information " to get latest news, interesting things and hot topics in the IT industry, and controls the hottest and latest Internet news, technology news and IT industry trends.