In addition to Weibo, there is also WeChat
Please pay attention
WeChat public account
Shulou
2025-04-04 Update From: SLTechnology News&Howtos shulou NAV: SLTechnology News&Howtos > Network Security >
Share
Shulou(Shulou.com)06/01 Report--
Successfully install Nexus 1000V n1000v-dk9.5.2.1.SV3.1.10 in vSphere ESXi6
After more than 10 days of installation and debugging, Nexus 1000V n1000v-dk9.5.2.1.SV3.1.10 was successfully installed in vSphere ESXi6.
There are some experiences:
1. Nexus1000V-install_CNX.jar (11822865 bytes) cannot be used to install VSM in vSphere ESXi6, and can only be used to install VSM in ESXi5.5 at most. It can only be used to install VEM in ESXi6.
I installed vCenter-Server-Appliance VCSA-all-6.0.0-3343019, and I can install VSM using Deploy OVF Template in vCenter in ESXi6.
2. Note: the network card of the added VEM host is set to forced speed (10m, 100m, 1000m) and forced half-duplex full-duplex according to the situation, and the network of adaptive VM is not available, or the time is not available. Nexus1000V does not support adaptation.
3. L3 layer 3 mode finally works. After adding host, you must migrate the host network management vmk0,VSM at the same time. You can already see VEM in the port-profile type vethernet configuration. The key point is that capability l3control must be added in the port-profile type vethernet configuration.
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2015, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
Owned by other third parties and used and distributed under
License. Certain components of this software are licensed under
The GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
Such license is available at
Http://www.opensource.org/licenses/gpl-2.0.php and
Http://www.opensource.org/licenses/lgpl-2.1.php
N1K-15# show module
Mod Ports Module-Type Model Status
10 Virtual Supervisor Module Nexus1000V active *
3 1022 Virtual Ethernet Module NA ok
Mod Sw Hw
1 5.2 (1) SV3 (1.10) 0.0
3 5.2 (1) SV3 (1.10) VMware ESXi 6.0.0 Releasebuild-3380124 (6.0)
Mod Server-IP Server-UUID Server-Name
1 x.x.x.150 NA NA
3 x.x.x.207 4c4c4544-004a-5910-8052-c7c04f323358 NA
* this terminal session
N1K-15#
4. The most important thing is the configuration of port-profile. The upper interface should be configured as trunk, and the lower port of VM should be configured as access. You can specify a dedicated system vlan, or you can share vlan 1 for all.
5. The most important configuration sample of port-profile has been tested and passed. You can copy and paste directly into the SSH interface for execution.
Config t
No port-profile type ethernet Uplink-ESXi215
No port-profile type vethernet Veth-ESXi215
Port-profile type ethernet Uplink-ESXi215
Vmware port-group
Switchport mode trunk
Switchport trunk allowed vlan all
No shutdown
System vlan 1
State enabled
Port-profile type vethernet Veth-ESXi215
Vmware port-group
Capability l3control
Switchport mode access
Switchport access vlan 1
No shutdown
System vlan 1
State enabled
Copy running-config startup-config
End
Show running-config port-profile
Welcome to subscribe "Shulou Technology Information " to get latest news, interesting things and hot topics in the IT industry, and controls the hottest and latest Internet news, technology news and IT industry trends.
Views: 0
*The comments in the above article only represent the author's personal views and do not represent the views and positions of this website. If you have more insights, please feel free to contribute and share.
Continue with the installation of the previous hadoop.First, install zookooper1. Decompress zookoope
"Every 5-10 years, there's a rare product, a really special, very unusual product that's the most un
© 2024 shulou.com SLNews company. All rights reserved.