Shulou(Shulou.com)06/01 Report--

Today, I will talk to you about how to install CentOS6.5 under VMware Workstation9. Many people may not know much about it. In order to make you understand better, the editor has summarized the following for you. I hope you can get something according to this article.

Download the CentOSer6.5 image file.

Http://mirrors.usc.edu/pub/linux/distributions/centos/6.5/isos/

Create a new virtual machine and name it CentOS6.5.

1. Select "Create a New Virtual Machine" in the VMware Workstation 9 home page to create a new virtual machine.

2. Select "Custom (advanced)" to customize (advanced) configuration.

3. Default, next step

4. Select "I will install the operating system later." and install the operating system later.

5. Select "CentOS" for the next step

6. Set the custom virtual machine name, set it to "CentOS", set the storage location of the virtual machine, and set it to "D:\ Document\ Virtual Machines\ CentOS". It can be set according to personal preference.

7. Default, next step.

8. Set the memory of the virtual machine, which can be set according to the memory of the personal computer, and 2048MB can be set here.

9. Set the network connection mode and use the NAT mode.

10. Default, next step.

Select "Create a new virtual disk" to create a new virtual disk.

12. Default, next step.

13. Specify the disk capacity, which is 20GB here; check "Split virtual disk into multiple files" to split the virtual disk into multiple files.

14. Default, next step.

15. List the specific information of the virtual machine here, click "Finish" to finish.

Third, set up the virtual machine image file directory.

1. Open the settings window for the new virtual machine CentOS.

two。 Sets the location of the operating system image file .iso in the virtual machine.

Start the virtual machine and install CentOS6.5

1. Start the virtual machine.

2. Select "Install or upgrade an existing system" to install or upgrade an existing system.

3. Whether to test the CD media, select "Skip" to skip.

4. Next step.

5. Choose the language. Here, choose "English (English)", English.

6. Select the keyboard, default, next step.

7. Select the installation device and select "Basic Storage Devices", the basic storage device.

8. Select "Yes,Discard any data", "Yes, ignore all data", and next.

9. Set the hostname, which is the next step by default.

10. Select the time zone, select "Etc/GMT+8", Beijing time zone.

11. Set the administrator root password.

12. The prompt password here is too simple. Select "Use Anyway" and ignore it.

13. Select the installation type, select "Create Custom Layout" and create a custom layout.

14. It is shown here that the current idle control is 20473MB. Click "Create" to create a partition.

15. Select "Standard Partition", the standard partition.

Create the first mount point: / boot, size: 128MB, file system type: ext3.

17. Continue to create partitions and click "Create".

18. Also select "Standard Partition", the standard partition.

19. Create a swap partition with a size of 2000MB.

20. Continue to create / partition and click "Create".

21. Also select "Standard Partition", the standard partition.

22. Create the root directory "/", size: select all available space, file type: ext3.

23. As shown in the figure, the next step is the spatial distribution after zoning.

24. Select "Format" to format.

25. Select "Write changes to disk" to write the changes to disk.

26. Next step.

27, default is "Minimal", here select "Desktop" desktop, select "Customize Now", now customize.

28. Select the installer you need, next.

29. Installation is under way.

Click "Reboot" to restart the system.

31. CentOS system is being restarted.

32. Enter the user name and password to log in to the system after startup.

Virtual machine network configuration

1. The IP of the virtual gateway VMnet8 of the host is set to be obtained automatically. The specific steps are as follows: right-click "Properties", then select the IPV4 line, click "Properties", and change it to get automatically.

2. by the same token, modifying the "local connection" is also obtained automatically.

3. "Virtual Machine"-"Settings", select NAT for the network adapter.

4. "Edit"-"Virtual Network Editor" select VMnet8, click NAT (share host IP address with virtual machine), and check DHCP (both boxes are checked).

Click "apply".

5. Enable VMware DHCP Service and VMware NAT Service services in the host (windows7).

Net start "VMware DHCP Service" net start "VMware NAT Service"

It's easy to write a script:

Create a new file: enable the VMware service .bat

Edit content Save:

[plain] view plain copy

Net start "VMware DHCP Service"

Net start "VMware NAT Service"

Pause

When you double-click "Open VMware Service. bat", you can easily open the VMware server.

Opening effect:

6. Test, ping in CentOS.

After reading the above, do you have any further understanding of how to install CentOS6.5 under VMware Workstation9? If you want to know more knowledge or related content, please follow the industry information channel, thank you for your support.

Welcome to subscribe "Shulou Technology Information " to get latest news, interesting things and hot topics in the IT industry, and controls the hottest and latest Internet news, technology news and IT industry trends.