Shulou(Shulou.com)06/01 Report--

This article will explain in detail how to configure the primary/secondary DNS server in win2003. Xiaobian thinks it is quite practical, so share it with you as a reference. I hope you can gain something after reading this article.

The company uses a domain environment to build DNS servers. Other information is as follows:

SVR1 Primary DC1/DNS: IP address 192.168.1.22/24 (NIC 1) IP address 192.168.0.44/24 (NIC 2)

SVR2 secondary DC2/DNS: IP address 192.168.1.23/24 (NIC 1) IP address 192.168.0.45/24 (NIC 2)

Note: NIC 2 is used for network load balancing clustering!

Install DNS services:

Win + R → appwiz.cpl Enter to open Add/Remove Programs, as shown below:

650) this.width=650;">

The rest is OK → Next → Select Source CD…It's relatively simple! hehe

II. New areas:

(1) Open the DNS service console, as shown below:

Win + R → dnsgmt.msc Enter, open the DNS Service Console, and create a new zone, as shown below:

650) this.width=650;">

Next, the interface pops up, as shown below:

650) this.width=650;">

After the next step, as follows:

650) this.width=650;">

650) this.width=650;">

Next → Done!

(2) Create a new reverse search area:

Refer to "Forward Search Area" to complete the previous steps. Note when you see the following figure:

650) this.width=650;">

The rest is very simple… ^_^ …

III. Records of main resources: Note: those frequently used by enterprises, others omitted!

(1) Create a new record for Host A:

650) this.width=650;">

650) this.width=650;">

Test ha, can the analysis succeed:

650) this.width=650;">

As you can see from the above picture, the analysis was obviously successful!

(2) Thinking: How do you create something like this? Similar to new host A record!

650) this.width=650;">

IV. Configuration of interface:

650) this.width=650;">

650) this.width=650;">

V. Transponder configuration:

650) this.width=650;">

Advanced DNS settings:

(1) DNS zone transfer: Note: Settings on the master DNS! SVR1

650) this.width=650;">

650) this.width=650;">

650) this.width=650;">

The following figure shows the region copy settings for reverse lookup regions:

650) this.width=650;">

(2) Set DNS zone transport on SVR2: Note: Settings on secondary DNS! SVR2

First test connectivity and resolution success:

650) this.width=650;">

As you can see, they all succeeded!

* After installing DNS service on SVR2, Win + R → dnsmgmt.msc Enter, the following interface will appear:

650) this.width=650;">

Next, the following interface appears:

650) this.width=650;">

650) this.width=650;">

650) this.width=650;">

650) this.width=650;">

Let's do the following:

650) this.width=650;">

650) this.width=650;">

650) this.width=650;">

650) this.width=650;">

Next → Done! OK, let's see if we're synchronized again. Please watch carefully!^_^

650) this.width=650;">

When SVR1 and SVR2 are running normally, they operate on the client. The analysis is as follows:

650) this.width=650;">

Below we simulate SVR1 failure, disable the NIC, and then operate on the client as shown below:

650) this.width=650;">

Primary/secondary DNS server configuration complete!

About "win2003 primary/secondary DNS server how to configure" this article is shared here, I hope the above content can be of some help to everyone, so that you can learn more knowledge, if you think the article is good, please share it to let more people see.

Welcome to subscribe "Shulou Technology Information " to get latest news, interesting things and hot topics in the IT industry, and controls the hottest and latest Internet news, technology news and IT industry trends.