Shulou(Shulou.com)06/03 Report--

This article mainly explains "how to install multiple network cards in the Netware server". Interested friends may wish to have a look. The method introduced in this paper is simple, fast and practical. Let's let the editor take you to learn how to install multiple network cards in the Netware server.

If only one network card is installed on the server when the network is expanded, and all workstations use the bus structure to access the Internet, then the access speed will be very slow. In addition, if a workstation fails while surfing the Internet, all workstations will be affected and cannot work.

We can install multiple network cards in the server to solve the problem. In this way, not only the work of the server is stable, and the Internet speed of the workstation will be greatly improved, but if there is a workstation failure, it will only affect those workstations that share a network card with the workstation, but not those workstations that use other network cards. This paper takes the installation of three network cards in the NetWare server as an example.

Installation and setup

Ready to install the network card (preferably the same model, different, but must be compatible with NE2000), first insert a network card into the server, and then turn on the server, run the network card diagnostic program Diag9008.exe that comes with the card in the DOS state. In the dialog box that appears, the diagnostic program will tell us that the default Ihandle O address of the network card is 300H, interrupting INT=3H. Select the option to configure the network card, change the ID O address of the network card to 340H, change the interrupt to INT=5H, then save the configuration, return to the DOS state, and shut down.

Insert the second network card into the server, reboot, follow the above method, change the I _ Unio address of the second network card to 320H, change the interrupt to INT=4H, save the configuration, return to DOS and shut down.

Finally, insert the third network card into the server, after running the diagnostic program, the diagnostic program will tell us that there are three network cards on the server, and the third network card has a 300H address, interrupt INT=3H (this is the default value of the network card, do not need to change it), save the configuration and return it to the DOS system, the network card will be installed successfully.

Configure NetWare

After the network card is installed, you have to call the driver of the network card in the NetWare system before you can use it. The specific method is to start the server, execute the load install command at the colon prompt, select the System Options option, then select the Edit Autoexec.ncf option, and change the contents of the Autoexec.ncf file to:

File server name LZEZ

IPX internal net 1

Load NE2000 Port=300 Int=3 Frame=ETHERNET_802.3

Bind IPX to NE2000 net=3

Load NE2000 Port=320 Int=4 Frame=ETHERNET_802.3

Bind IPX to NE2000 net=4

Load NE2000 Port=340 Int=5 Frame=ETHERNET_802.3

Bind IPX to NE2000 net=5

Load monitor

Then save the disk and exit the system.

The network card is connected with the network operating system

After the above two steps, we can surf the Internet according to the new configuration. The specific approach is to connect the workstations to different network cards and start the server. During the startup process, the following message appears:

Several boards are using the NE2000 LAN driver

1. NetWare NE2000 v3.11 (910131) using I Port O Port 300h to 31FhLaw interrupt 3h

Frame type:ETHERNET_802.3

2.NetWare NE2000 v3.11 (910131) using I Port O Port 320h to 33FhRecence interrupt 4h

Frame type:ETHERNET_802.3

Select board to bind:

There are several network cards in the server that are using the drivers of the NE2000 LAN, and list the Imax O address of each network card and the interrupt number used, we have to choose how many network cards to connect. At this time, enter the number 2 after Select board to bind:, and then enter the enter server to start successfully.

If there are three network cards, enter the number 2 and enter, a message will be added:

3.NetWare NE2000 v3.11 (910131) using I Port O Port 300h to 35Fhre interrupt 5h

Frame type:ETHERNET_802.3

Select board to bind:

Enter 3 at this time, and then enter enter.

At this point, I believe you have a deeper understanding of "how to install multiple network cards in the Netware server". You might as well do it in practice. Here is the website, more related content can enter the relevant channels to inquire, follow us, continue to learn!

Welcome to subscribe "Shulou Technology Information " to get latest news, interesting things and hot topics in the IT industry, and controls the hottest and latest Internet news, technology news and IT industry trends.